Aviom AV-P2 | 2 Analog Output A-Net Digital Audio Stream

Aviom AV-P2 | 2 Analog Output A-Net Digital Audio Stream

Product Code: AV-P2
Availability: In Stock
MSRP: $736.00
Minimum Advertised Price: $685.00
Your Price: Click For Price
    - OR -   Add to Compare

The AV-P2 Output Module provides up to two channels of analog outputs from a Pro16® A-Net® digital audio stream. The analog output level for each channel is set with front-panel DIP switches.

Each AV-P2 in a system receives a 16-channel A-Net stream originating at a Pro16 input module, console interface card, or Pro64® audio network (via the ASI A-Net Systems Interface module).

Channel Selection

A front-panel rotary switch allows the output to be set to any one of those 16 source channels. If the selected channel is part of a stereo pair (set at the input module), the left and right channels are automatically routed to the left and right outputs on the AV-P2. If the selected channel is not part of a stereo pair, the selected mono channel's audio is routed to both the left and right outputs.

System Flexibility

AV-P2 modules can be connected in any combination of serial or parallel connections, using Pro16 A-Net Distributors. There is no limit to the number of devices that can be daisy chained, or to the number of parallel splits in a single system. The AV-P2 is compatible with all Pro16 Series products and can be used in any combination with A-16II and A-16R Personal Mixers, the AN-16/o Output Module, and the A-16D and A-16D Pro Distributors.

Audio is distributed to the AV-P2 over standard Cat-5e cables, using Aviom's A-Net digital audio protocol. A-Net supports plug-and-play installation, real-time distribution with sub-millisecond latency, and long cable runs up to 500ft/150m. Power can be supplied to the AV-P2 with an external DC power supply or over the Cat-5e cable (with an A-Net Distributor). Additionally, Pro16 A-Net audio streams can be transmitted over single- or multi-mode fiber optics using certain standard third-party media converters.

Mounting Options

The AV-P2 has reversible mounting flanges. Two AV-P2 modules can be mounted side by side on a standard 1U rack tray.

Features:

  • Provides 1- or 2-channel analog output from a Pro16® A-Net® stream
  • Independently selectable output levels for left and right channels
  • 48kHz, 24-bit D/A converters
  • Optional power over Cat-5e using a Pro16 A-Net Distributor
  • Reversible mounting flanges

Specifications:

Audio Outputs: 2, impedance balanced line-level
5.0 mm Euroblock connectors, female, panel- mount
2 male Euroblock connectors supplied in box
Screw terminals: Audio +; Audio -; Ground
Channel Selection: 16-position rotary switch
D/A Conversion: 48kHz, 24-bit
Output Levels: Maximum Output Level: +18dBu
Output Level Trim from 0dB to -35.9dB in 1.5dB steps;
6-position DIP switch, per channel
Indicators: LEDs; red: Power, green: A-Net Active, yellow: Stereo Pair
Output Impedance: 100 ohms
Signal to Noise:
(unweighted)
93dB typical, A/D to D/A
Measured from AN-16/i Input Module to AV-P2
Freq. Response: 4Hz-22kHz +0.2dB/-3dB
THD +N: -93dB at -10dBFS
Crosstalk: -85dB at 1kHz
Bit Error Rate (BER): 10-12
Digital Connections: A-Net In: 1; A-Net Out: 1; RJ45 connectors
Pro16 A-Net®: Uses unshielded Cat-5e UTP (or better) cable
Latency: <0.880 msec (measured from analog input to analog output)
Power Supply:
   Input Voltage
   Output Voltage
   Plug Size
External, DC, universal switching type
100-240 volts, 50/60Hz, 30VA
18-24 VDC, 0.5 amp
2 mm, locking, center pin hot

Dimensions:

7.45" (189.2 mm) wide x 7" (177.8 mm) deep; 1U high
Weight: 3.4 lbs (1.54 kg)

 

Copyright © 2019, Springtree Media Group, LLC. All rights reserved.
Springtree Media Group, LLC is not responsible for typographical errors.
Prices and specifications subject to change without notice.